electronica 2026 roundup: What stood out in Munich

A garden can look perfectly manageable until the leaves come down. Suntek found that its single-camera mower could navigate without a perimeter wire, yet a patch of bare soil or a dark line on the ground could confuse it about where the grass was. According to Fibocom, the team went back to footage from real gardens and retrained the model before taking it into production. If you’ve ever looked out of the window in November and decided the lawn can wait, you can probably see where the mower was coming from.
Across four days and 3,512 exhibitors, there were plenty of ways to see what happens when a promising idea has to fit an actual product. A team developing an onboard charger found room by taking out the bulk capacitors between its conversion stages. A supplier trying to cool an AI rack had to specify what it needed from the building’s water supply. And on the manufacturing side, the most interesting thing about Infineon’s 300 mm silicon carbide wafer was what the company had managed to make on it using equipment it already owned.
More room on the wafer
Moving from a 200 mm wafer to a 300 mm one gives you 2.25 times the surface area, but the economics depend on how many of the devices on that surface come out working. At Villach, Infineon used existing silicon manufacturing equipment to make functional power devices on a 300 mm silicon carbide wafer. It reckons the larger format has room for roughly 2.3 times as many chips per wafer. The eventual cost per good die will depend on yield and on what it costs to get the wafer onto the line.
Some of that work is taking place in Dresden, where the company has shown that its Cold Split process can separate 300 mm wafers from a silicon carbide crystal. Infineon says it loses less material than wire sawing, which matters because getting more usable wafers out of each crystal improves the economics before fabrication even starts. There’s still work to do with customers and partners on when 300 mm production can ramp. In the meantime, the multiyear agreement Infineon signed with Wolfspeed in October is for 200 mm substrates.
At the inverter end of the business, onsemi already has a 750 V automotive bare die available from its new EliteSiC M4 trench platform, with products up to 1,200 V expected from 2027. It claims up to 30% higher power density and 35% lower losses compared with its previous generation. How much of that carries through to a finished inverter depends on the design. As Harald Hartel of Schaeffler put it in onsemi’s announcement, “traction-inverter design becomes a tighter balancing act between efficiency, thermal performance, power density and reliability”. Nexperia’s new 750 V trench MOSFETs brought a more immediate choice for board layouts, with a compact TOLL surface-mount package joining its existing options and industrial and automotive-qualified variants available.
The parts a new switch lets you leave out
If current has to flow either way through a switch when it’s on, and the switch has to block either polarity when it’s off, a familiar way to do it is with two transistors back to back. Infineon’s 650 V bidirectional GaN device puts those functions on one die. The reason it was worth following beyond the power electronics forum was that Visteon and SHINRY had a specific job for it, in an onboard charger they’re developing with Infineon. Their circuit combines functions usually handled by separate stages, allowing them to dispense with the bulk capacitors between the two.
The design supports 22 kW charging from three-phase AC and 19.2 kW from single-phase AC, and can also send power back out of the vehicle. Taking out the intermediate capacitors can make the charger easier to fit, particularly where space is tight. The comparison with a conventional two-stage unit will get more interesting when the development team can show how the combined converter behaves at different loads and temperatures, including when the power is flowing in the opposite direction.
What the rack needs from the building
Delta’s 4U coolant distribution unit can transfer up to 140 kW of heat, provided it has a 4 °C approach temperature. The unit transfers heat from the rack coolant to facility water, so getting that capacity out of it depends on what the building can deliver as well as what Delta can fit in the rack. The company was also showing 800 V DC and ±400 V DC distribution, along with server power supplies rated up to 5.5 kW.
Follow that power towards the processor and the voltages come down sharply. Vishay’s reference designs included a 12 kW converter that stepped 800 V down to 50 V and a separate 32-phase design that took power from a 48 V bus to the GPU. A higher voltage keeps the current down further upstream, whereas at the processor the much lower supply voltage means the current is high again and the distance it travels across the board starts to matter. There’s a similar distinction on the data side. Keysight was testing 1.6 Tb/s links at 100 and 200 Gb/s per lane, and it’s the speed of each lane that sets the demands on the individual electrical or optical channel.
Those engineering decisions already have a substantial business behind them. Infineon reported €1.7 billion in revenue from AI data centre power products in its 2026 financial year, more than double the previous year’s figure. In his published remarks for the company’s Munich press conference, chief executive Jochen Hanebeck said it had increased production “even though we were unable to meet all customer requests”. Infineon put the combined potential revenue from multiyear supply agreements and capacity reservations at more than €10 billion, including deals still being negotiated.

Before two chiplets go into the same package
A package can look feasible on paper until you work out where the connections have to go and how the heat will get out. Imec’s contribution at SEMICON Europa was a baseline process for a silicon interposer with multiple routing layers, through-silicon vias and microbump pitches down to 20 µm. Once the NanoIC design kit comes out, which imec is targeting for early 2027, teams will be able to use Cadence and Synopsys tools to evaluate designs against that process. Low-volume prototyping is a later step.
For a carmaker, the appeal is being able to carry most of a processor design from one vehicle to the next and swap the die that needs more performance. Even when the new die uses the same interface, it can change the way heat spreads through the package or how signals behave under load. Either can mean repeating part of the qualification work. The joint requirements from Japan’s ASRA and imec, released the same week, give suppliers somewhere to start agreeing what their dies will need to do together.
Keeping the radio reachable on a battery
A battery-powered sensor may have very little to do for most of the day, apart from waiting for a message it has to catch when it arrives. Fraunhofer IIS’s answer is a separate wake-up receiver that can listen on 433 MHz, 868 MHz and 2.4 GHz at the same time, drawing 7 µA from a 1.5 V supply while the main radio or processor sleeps. A device that needs to keep two networks within reach has a different problem, which Nordic’s nRF71 addresses with independent radios that can receive concurrently. The device can maintain its Wi-Fi connection while it listens for Bluetooth LE or Thread, and Nordic says the best-case standby draw is a twentieth of that of its nRF70 Wi-Fi products. How often the device wakes up to transmit still has to go into the battery calculation. The parts are sampling with selected customers.
The same calculation gets harder when the device needs to recognise a word rather than simply hear a radio signal. Ambient Scientific’s processor has its own power figure for keyword detection, but the microphone and the supporting circuit have to stay on as well. Working with CELUS puts those components into the design alongside the processor, where their draw can be accounted for while there’s still room to make changes. Weebit Nano’s Matrix research platform takes aim at another part of the power bill, letting researchers investigate whether doing calculations in resistive memory can cut the energy spent moving data between memory and the processor.
Keeping an existing design in production
When a product still has years of production left, changing the storage can land a surprising amount of work back with the design team. Sandisk’s iNAND CL EM181 moves to newer NAND while keeping the e.MMC 5.1A host interface and using the same package footprint across capacities from 64 GB to 256 GB. Sandisk quotes sequential reads of up to 300 MB/s and writes of up to 225 MB/s, but for an established design the useful part may be how little has to change on the host side.
An obsolescence notice can set off a similar job, only this time the first task is finding out which boards contain the part in question. Luminovo showed how an assistant could search bills of materials and check supplier data, bringing the list of affected products closer to the information a buyer needs to decide whether to secure stock or qualify a replacement. How much stock a supplier can actually ship is a separate matter. Nexperia said its back-end expansion in Malaysia and the Philippines had reached approximately 55 billion parts of installed annual capacity by October, and its court-appointed officials confirmed that further capacity was being developed at both locations and through third parties. That figure describes the scale of the expansion. Availability still comes down to the particular device and where it can be made and qualified.
A bearing that doubles as a sensor
As a rolling bearing takes more load, the lubricant film and the area carrying that load change, and with them the electrical impedance across the contact. Measure that while the bearing is turning and you have a way to see what’s happening inside it using the bearing itself as the sensor. The approach won HCP Sense the Fast Forward award, and there’s already a practical example in development testing, where Knorr-Bremse used it to study lubrication while there was still time to change the design.
The last problem worth mentioning starts once the electronics have been thrown away. Karlsruhe Institute of Technology’s CellScan team is investigating whether impedance spectroscopy can spot a lithium-ion battery among household rubbish, while it’s still in the wheelie bin and before it reaches the lorry’s compactor. It was a student project at the show, and it has an unusually clear idea of what a good day looks like. The bin gets emptied and nothing catches fire.



